FOXBORO

FOXBORO 2AX-ALM-AR – Foxboro Alarm Module

Low Temperature Operative Limit of Electronics Housing Extended Down to -50°C (-58°F)

Not available with sensors and seals with Inert fill, Structure Codes 78 and 79.

or DIN Options -D2. -D4. -D6. and -D8

Vent Screw in side of Process Cover (with 316 ss process covers only)

Not available with seals, DIN construction options, or Structure Codes 78 and 79

Model-J-V (h)

Supplemental Customer Tag (Stainless Steel Tag wired onto Transmitter)

Examples: IGP20-D20B21F-M1Z2; IAP20-DS3C11F-T-T

a. Maximum overrange pressure is 2.1 MPa (300 psi); temperature limits are -7 and +82°C (20 and 180°F).

b. Transmitter and Pressure Seal Model Codes are both required. See PSS 2A-1Z11 A for the various pressure seal model codes.

c. Remote Seal Models that may be specified are PSFPS, PSFES, PSFAR, PSTAR, PSISR, PSSCR, and PSSSR.

d. Span Limit Code A is not available with pressure seals (Structure Codes F1. F2. S3. S4. SC, SD).

e. Span Limit Codes E and F are not available with Structure Codes 78 and 79 (PVDF insert in HI Side Cover).

A cover lock is provided as standard with Electrical Safety Codes D, B, G, and V.

g. Not available when Remote Mount or Direct Connect Pressure Seals are specified.

h. Pressure derated. See derating table in specifications section.

Temperature limits derated to 0 and 60°C (32 and 140°F). Also Mounting Sets -M1 and -M2 not available.

When -X3 is specified, the standard bolting is replaced with 17-4 ss bolts and nuts. Therefore, there is no need to specify Option-B2

when selecting the Chlorine Service Option -X3.

Available with Electrical Safety Code D only.

OTHER FLASH SERIES 2
OVATION 1B30023H01
OVATION 1B30035H01
OVATION 1C31157G02
Ovation 1C31238H01
OVATION 1X00458H01
OVATION 5X00070G04
OXIDE 0020-31655
P&B C87-11006 REV F/C10-12010 REV F
P+F HIC2025
P+F HIC2031
P+F HICTB08-YC3-RRB-KS-CC-AM08
P+F HICTB16-YC3-RRB-AK-CC-DX32
P+F HID2030

k. Not available with DIN construction options. For stainless steel bolts with DIN construction, specify -D5 to -D8. as required.

m. Standard offering with IAP20 Transmitters when pressure seals are used. However, -G1 is a required option with IGP20 Transmitters

when pressure seal (Structure Codes S3. S4. F1. F2. SC, and SD) will be used in vacuum applications. This option substitutes

vacuum service metal gasket for standard PTFE process cover gasket

TRADITIONAL STRUCTURE (Figure8)

This structure is where the process connections

are at 90° from the transmitter centerline.

Vertical and horizontal mounting are provided for

sensor cavity venting and draining.

LOW PROFILE STRUCTURE LP1 (Figure9)

This structure has process connections that are

in line with the transmitter centerline. It is

compact, and its light weight is ideal for direct

mounting to the process. An adapter plate

(Options -P1 to -P8), shown in Figure10 with the

LP2. is offered for mounting to a Coplanar™

manifold. Sensor cavity venting and draining is

provided for both vertical and horizontal

installations.

LOW PROFILE STRUCTURE LP2 (Figure10)

This structure, as with the LP1. is an in-line

design which can be direct or bracket mounted.

It is used for vertical installations, and can also

be installed on existing Coplanar manifolds

using an adapter plate (Options -P1 to -P8).

Sensor cavity venting and draining are also

provided.

Wide Rangeability

Five d/p Cell range sensors cover measurement

spans from 0.125 kPa to 21 MPa (0.5 inH2O to

3000 psi). This high turndown capability means that

most differential pressure applications are satisfied

with only these five ranges, simplifying your spare

transmitter and spare parts requirements.

Sensor Corrosion Protection

Choice of 316L ss, Co-Ni-Cr, Nickel alloy, Monel,

Gold-Plated 316L ss, and Tantalum materials. High

corrosion resistance of Co-Ni-Cr (TI 037-078) means

long service life without extra cost for exotic

materials. See TI 37-75b for process applicability

with Co-Ni-Cr and other wetted parts materials.

Flameproof Design

Meet Agency flameproof and zone requirements.

Process Connectors

Removable, gasketed process connectors allow a

wide range of selections, including 1/4 NPT,

1/2 NPT, Rc 1/4. Rc 1/2. and weld neck connections.

For very corrosive chemical processes, 1/2 NPT

PVDF inserts are installed in the HI- and LO-side

316 ss covers when a traditional structure is used,

and used as the process connectors.

Leave a Reply

Your email address will not be published. Required fields are marked *