Keba Ketop T50 025 Ces/ 84679/ 02 Teach Panel 24VDC Control
Temperature inputs J, K, L – TM 2×0/A only
TM 220/A TM 240/A
Number 3 6
Thermoelement types J, K, L
Resolution 14 bit
Galvanic isolation Yes, from the control electronics and between one another
Electric strength: 707 V DC
Sensor failure detection Yes
Measurement ranges Type J (Fe-CuNi): -100 °C … +700 °C
Type K (NiCr-Ni): -100 °C … +1000 °C
Type L (Fe-CuNi): -100 °C … +700 °C
Measurement principle Integrated
Measurement time 100 ms
Input resistance >10 kΩ
Connections Pluggable connection terminals, gold-plated contacts, nominal cross section: 1.5 mm²
Intrinsic deviation ±1.0 °C max. absolute measurement deviation at 25 °C ambient temperature at the
module over the entire measurement range (±0.5 °C typical)
Temperature measurement sensor error ±1.0 °C max. absolute measurement deviation at 0 °C to 70 °C ambient temperature
(±0.5 °C typical)
Operational deviation ±1.5 °C max. absolute measurement deviation at 0 °C to 55 °C ambient temperature
at the module over the entire measurement range (±1.0 °C typical)
Thermal settling time 20 minutes
Error with external compensation With external sensor TE 220/A: ±0.5 °C
PT100 temperature inputs – only TM 225/A
Number 4x PT100
Resolution 14 bit
Galvanic isolation No
Sensor failure detection Yes
Measurement range-100 °C … 850 °C
Linearization method Internal
Input type 4- or 2-conductor measurement
Calibration Yes
Constant current output 600 μA (each type)
Scan repeat cycle 2 ms
Input impedance in signal range 10 MΩ
Input filter characteristic First order
Input filter characteristic –
transfer frequency 15 Hz
Conversion method Successive approximation
Monotonicity without error codes Yes
Common mode range ≤ 13.5 V
Common mode rejection ratio > 80 dB
Value of the lowest bit (LSB) 0.058 °C
Maximum permitted continuous load
(without damage) ≤ 30 V
Typ. temp. coefficient measurement error ≤ 10 ppm of scale end value / °C
Max. temp. coefficient measurement error ≤ 40 ppm of scale end value / °C
Largest error at 25 °C ≤ 0.02 % of scale end value / °C
Averaging Moving average over 100 ms
Dimensions, weight
TM 220/A TM 240/A TM 225/A
Height 120 mm
Width 22.5 mm front plate / 32.5 mm incl. K-bus plug
Depth 100 mm
Weight 142 g 142 g 134 g
Environmental conditions
Operating temperature +5 °C … +55 °C
Storage temperature-40 °C … +70 °C
Relative air humidity 10 % to 95 % (non-condensing)
Vibration resistance / shock resistance Acc. to EN 61131-2
General
TM 220/A TM 240/A TM 225/A
Supply voltage 24 V DC from K-bus, 5 V DC from K-bus
Overvoltage category II
Protection class III acc. to EN 61131-2
Addressing on K-bus Via 16-digit address switch, on the side
Connection terminals Open – pitch: 5.08 mm
Max. power consumption K-bus 24 V 1.6 W 1.6 W 2.5 W
Max. power consumption K-bus 5 V 0.5 W 0.6 W 0.3 W