EATON CORPORATION BA43P RELAY
Redundant power paths assure high fault-tolerance and
optimum uptime. Galvanic isolation separates input from
output, filtering line noise and surges. FERRUPS also features
precision voltage regulation with no battery discharge down to
38% below nominal (depending upon load) as well as over 80
user-programmable diagnostic and communications functions.
FERRUPS models include free Eaton Software Suite power
management software with connectivity cable and are
BestLink SNMP/Web-ready for remote management.
FERRUPS covers up to $250.000 for damage to connected
equipment resulting from a spike or surge (US and Canada
only).
secure operation.Ever Electronics SDMWD170 VB231D
SICK CDB650-204 1064114
Merlin Gerin Power Logic PM820MG
JETTER LCD11 788-1-0068 Control Panel / Jetter Processor Display Panel
Relay M-BUS MR006DL RS232C
Reliance Electric 804.89.01E GD.719.48.00-C
TELEMECHANICAL SOFT STARTER ATS48D22Q
CFS WEERT 11014652 PLATE
Omron GRT1-AD2 Analog Input Unit
BECKHOFF CX1000-0121 N003 – N005 – N001 – N0000 – COOL with SSD-C02GI-3500
Lenze DSVARS 071-22 1.7kW DSVARS07122
AALBORG GFM373 Mass Flow Meter Gfm
Siemens 6SL3210-1KE12-3AP2 SINAMIC G120CDP 0.75kw
Pilz Pnoz Xm14s1O 774600
AALBORG GFM373 Mass Flowmeter Gfm
B&R X67DO1332 Rev.L0
Lenze DSVARS 071-22 1.7 kW DSVARS07122
B&R 7EX477.50-1 Rev.C0
Siemens 6SL3210-5HB10-4UF0
ABB ALFA LAVAL 200-PSSG
Beckhoff AX2003 S60300-520 With Lightbus B200
KBS Pomp Drive 5003K00B00SI4 3kW
TELEMECANIQUE SOFT STARTER ATS48D22Q
EATON ES4P-221-DMXD1 EASY SAFETY ES4P221DMXD1
Allen-Bradley 22A-D6P0N104 2.2kW
Eaton’s Cutler-Hammer FP-4000 Feeder Protection Relay provides
complete 3-phase and ground overcurrent and voltage protection
plus metering. It may be used as primary protection on feeders, mains
and tie circuit breaker applications, and as backup protection for trans
formers, high voltage lines and differential protection. The relay is most
commonly used on medium voltage switchgear applications.
The FP-4000 takes full advantage of its microprocessor technology,
providing the user new freedoms and a wealth of data-gathering
features. The relay performs self-checking of all major hardware and
firmware protection elements to ensure their operation in the event of
a system or component electrical failure or fault. Protection functions
are well suited for main and distribution feeder circuit applications.
Programmable logic control functions make the FP-4000 relay ideally
suited for main-tie-main and main 1/main 2 transfer schemes.
The zone interlocking feature can be utilized for bus protection instead
of an expensive and complicated bus differential (87B) scheme.
The FP-4000 works directly with the Cutler-Hammer Digitrip 3000
and Digitrip MV relays. New breaker failure logic provides faster
remote backup clearing times for stuck breaker operation.
The FP-4000 provides trip and close circuit monitoring and alarming
features. It continually monitors the complete trip and close circuits
for continuity and readiness to trip. Open and close pushbuttons are
conveniently located on the front of the relay for local breaker operation.
Loss-of-vacuum monitoring is activated when the breaker is open.
Residual current is monitored and alarmed if detected.
Eaton operates an independent development center, the ‘Cybersecurity
Center of Excellence’ (CCoE), specifically designed to combat the threats
posed by cyber attacks. All Eaton products are regularly qualified for