KEBA

KEBA CU 313/C-SI / 63036 /01

Temperature inputs J, K, L – TM 2×0/A only

TM 220/A TM 240/A

Number 3 6

Thermoelement types J, K, L

Resolution 14 bit

Galvanic isolation Yes, from the control electronics and between one another

Electric strength: 707 V DC

Sensor failure detection Yes

Measurement ranges Type J (Fe-CuNi): -100 °C … +700 °C

Type K (NiCr-Ni): -100 °C … +1000 °C

Type L (Fe-CuNi): -100 °C … +700 °C

Measurement principle Integrated

Measurement time 100 ms

Input resistance >10 kΩ

Connections Pluggable connection terminals, gold-plated contacts, nominal cross section: 1.5 mm²

Intrinsic deviation ±1.0 °C max. absolute measurement deviation at 25 °C ambient temperature at the

module over the entire measurement range (±0.5 °C typical)

Temperature measurement sensor error ±1.0 °C max. absolute measurement deviation at 0 °C to 70 °C ambient temperature

(±0.5 °C typical)

Operational deviation ±1.5 °C max. absolute measurement deviation at 0 °C to 55 °C ambient temperature

at the module over the entire measurement range (±1.0 °C typical)

Thermal settling time 20 minutes

Error with external compensation With external sensor TE 220/A: ±0.5 °C

PT100 temperature inputs – only TM 225/A

Number 4x PT100

Resolution 14 bit

Galvanic isolation No

Sensor failure detection Yes

Measurement range-100 °C … 850 °C

Linearization method Internal

Input type 4- or 2-conductor measurement

Calibration Yes

Constant current output 600 μA (each type)

Scan repeat cycle 2 ms

Input impedance in signal range 10 MΩ

Input filter characteristic First order

Input filter characteristic –

transfer frequency 15 Hz

Conversion method Successive approximation

Monotonicity without error codes Yes

Common mode range ≤ 13.5 V

Common mode rejection ratio > 80 dB

Value of the lowest bit (LSB) 0.058 °C

Maximum permitted continuous load

(without damage) ≤ 30 V

Typ. temp. coefficient measurement error ≤ 10 ppm of scale end value / °C

Max. temp. coefficient measurement error ≤ 40 ppm of scale end value / °C

Largest error at 25 °C ≤ 0.02 % of scale end value / °C

Averaging Moving average over 100 ms

Dimensions, weight

TM 220/A TM 240/A TM 225/A

Height 120 mm

Width 22.5 mm front plate / 32.5 mm incl. K-bus plug

Depth 100 mm

Weight 142 g 142 g 134 g

Environmental conditions

Operating temperature +5 °C … +55 °C

Storage temperature-40 °C … +70 °C

Relative air humidity 10 % to 95 % (non-condensing)

Vibration resistance / shock resistance Acc. to EN 61131-2

General

TM 220/A TM 240/A TM 225/A

Supply voltage 24 V DC from K-bus, 5 V DC from K-bus

Overvoltage category II

Protection class III acc. to EN 61131-2

Addressing on K-bus Via 16-digit address switch, on the side

Connection terminals Open – pitch: 5.08 mm

Max. power consumption K-bus 24 V 1.6 W 1.6 W 2.5 W

Max. power consumption K-bus 5 V 0.5 W 0.6 W 0.3 W

SEW 31C450-503-4-00
SEW DFP
SEW DFP  8227241.12
SEW DFP 21A
SEW DFS56L/TF/RH1M/KK
SEW DIP
SEW EF-014-503
SEW MDF60A-0022-5A3-4-00
SEW MDF60A-0022-5A3-4-00(MDX60A0075-5A3-4-00)
SEW MDF60A-0075-5A3-4-00
SEW MDS60A0150-503-4-00
SEW MDV
SEW MDV 8222215.14.17
SEW MDV60A0075-5A3-4-0T
SEW MDV60A0110-5A3-4-00
SEW MHD093C-058-PG0-AN
SEW MKS51A005-503-50

Leave a Reply

Your email address will not be published. Required fields are marked *