FOXBORO FBM39 – Control module
Sensor Corrosion Protection
Choice of 316L ss, Co-Ni-Cr, Nickel alloy, Monel,
Tantalum, and Gold-Plated 316L ss materials. High
corrosion resistance of Co-Ni-Cr (TI 037-078) means
long service life in many difficult applications without
the extra cost for exotic materials. Also see TI 37-75b
for process applicability with Co-Ni-Cr and other
wetted parts materials.
Wide Rangeability
Gauge pressure measurement spans may be as low
as 0.12 kPa (0.5 inH2O) to as high as 35 MPa
(5000 psi) by choosing one of only six sensors, and
absolute pressure measurement spans may be as
low as 0.87 kPa (3.5 inH2O) to as high as 21 MPa
(3000 psi) by choosing one of only four sensors.
This provides exceptional measurement range
capability with a minimum of versions.
Process Connector
Removable, gasketed process connector (Figure 6)
allows a wide range of selections, including 1/4 NPT,
1/2 NPT, Rc 1/4. Rc 1/2. and weld neck connections.
For highly corrosive chemical processes, a 1/2 NPT
PVDF (Kynar) insert is installed in the HI-side 316 ss
cover and is used as the process connector. In these
applications, tantalum is used as the sensor
diaphragm materi
Flameproof Design
The transmitters are designed to meet Agency
flameproof and zone requirements.
Ease of Mounting Optional Two-Valve Manifold
Two-valve manifold, to isolate transmitter and to vent
pressure, is easily mounted directly to transmitter.
Vacuum Service
An LRL of -100 kPa (-14.7 psi, -1 bar) means that
vacuum measurements are easily handled with the
versatile IGP20 transmitter.
Vibration Effect
Total effect is ±0.2% of URL per “g” for vibrations in
the frequency range of 5 to 500 Hz; with a double
amplitude (DA) of 6.3 mm (0.25 in) in the range of 5
to 15 Hz, or accelerations of 3 “g” in the range of 15
to 500 Hz, whichever is smaller, for transmitters with
aluminum housings; and with a DA of 6.3 mm
(0.25 in) in the range of 5 to 9 Hz, or accelerations of
1 “g” in the range of 9 to 500 Hz, whichever is
smaller, for transmitters with 316 ss housings.
Process Wetted Materials
PROCESS CONNECTION
316L ss, cs, Monel, or Nickel alloy, or PVDF
SENSOR DIAPHRAGM
316L ss, Co-Ni-Cr, Monel, Tantalum, Nickel
alloy, or Gold-Plated 316L ss
GASKET
Glass-filled PTFE
Pressure Seal Diaphragm Material
Varies with pressure seal selected.
Reference Side Materials
Cover is 316 ss, and sensor diaphragm material is
same as for process wetted materials above.
Fill Fluid
Silicone Oil or Inert FC43. as specified.
Dimensions
Refer to “DIMENSIONS – NOMINAL” on page 36
and to Dimensional Print DP 020-447.
Approximate Mass
3.5 kg (7.8 lb) – with Aluminum Housing
4.2 kg (9.2 lb) – with Process Connectors
Add 1.1 kg (2.4 lb) – with 316 ss Housing
With Pressure Seals: See PSS 2A-1Z11 A.
| NEC | 136-551973-A-01 |
| NEC | 136-553623-A-01 |
| NEC | FC-9801F |
| NEC | FC-9821KE |
| NEC | FC-9821X MODEL1 |
| NEC | FC-9821X MODEL2 |
| NEC | G8NXAA5G |
| NEC | NEC |
| NEC | PC-9821XB10 |
| NEC | RSA-983/D |
| NEC | SC-UPCIN-3 |
| NEUGART | PLE120 |
| NEUGART | PLE120/115 |
| NEXUS CONTROLS | 369B1843G5009 |